See what your neighbors in Meadowbrook, PA are saying about Chud’s indoor air quality expertise. We’ll clean your ducts and clean your air to help you have better health in your home.
Local Reviews
for Meadowbrook, PA
Our Reviews by City
Great service
Ron - Meadowbrook, PA 19046
Came out quickly, heater now works.
Response from Chud Air Conditioning & Heating:
Ron, so glad we were able to get your system back to heating so quickly! Thank you for leaving Chud a 5 star review.
Prompt, Efficient, Courteous
Bob - Meadowbrook, PA 19046
Response from Chud Air Conditioning & Heating:
Bob, thank you for leaving Chud a 5 star review!
Wonderful service
Liz - Meadowbrook, PA 19046
They were wonderful. Efficient and courteous
Response from Chud Air Conditioning & Heating:
Thank you for sharing your experience Liz, everyone at Chud appreciates it!
Great service!
Jean - Meadowbrook, PA 19046
Excellent in all aspects
Response from Chud Air Conditioning & Heating:
Jean, thank you for the 5 star review! Everyone at chud appreciates it.
Great Service
Jean - Meadowbrook, PA 19046
Technician came on time. Provided service in a very professional manner.
Response from Chud Air Conditioning & Heating:
5 stars, thank you Jean!
Heating system yearly service check up
Mitch - Meadowbrook, PA 19046
We have used Chud for years and continue to be very satisfied, from start to finish. Tara, in the office was very helpful and Matt, our technician, was extremely thorough and knowledgeable. All my questions were answered, and I received great recommendations for the future maintenance of our system, so that it continues "to hum"!
Response from Chud Air Conditioning & Heating:
Hi Mitch, we appreciate the good review. Chud works hard to create a good experience and reviews like this make it all worth it!
Excellent Service
Harry - Meadowbrook, PA 19046
John was excellent in all phases. Chud is fortunate to have.
Response from Chud Air Conditioning & Heating:
Harry & Margaret, we couldn't agree more, we are lucky to have John! Thank you for the 5 star review.
Very knowledgeable and friendly technician
Tod - Meadowbrook, PA 19046
Response from Chud Air Conditioning & Heating:
The team here at Chud loves to see 5 star reviews! Thank you Tod.
Fast, Efficient and Pleasant as well
Bob - Meadowbrook, PA 19046
Our technician was on time, knowledgeable and efficient. Very pleased.
Response from Chud Air Conditioning & Heating:
The team here at Chud loves to see 5 star reviews! Thank you Bob & Ellen.
Super Nice. Very professional
John - Meadowbrook, PA 19046
Great service
Response from Chud Air Conditioning & Heating:
5 stars, thank you John!
Happy experience
Bob - Meadowbrook, PA 19046
Pleasant, efficient and knowledgeable technician. Fast response to emergency. Very fair pricing. We are long-term happy clients of this company.
Response from Chud Air Conditioning & Heating:
Hello Bob & Ellen. Chud works hard to create a good experience and reviews like this make it worth it!
Paul
Jean - Meadowbrook, PA 19046
Excellent service
Response from Chud Air Conditioning & Heating:
5 stars, thanks Jean!
Your technician, Paul, was the best- extremely knowledgeable,
Harry - Meadowbrook, PA 19046
Paul walked us thoroughly through the steps that he took to identify and fix the issue. He has great customer communication skills.
Response from Chud Air Conditioning & Heating:
Hi Harry! So glad you had such a positive experience working with Paul. Thank you for the review.
Matthew M.
Installed new Weil McLain boiler and Bradford white water heater. Project included adapted to boiler supply and return. Install 3 new Taco zone valves, new zone control board. Adapted to gas line. Installed new isolation valves and purge set up. New auto fill, and air separator also, installed boiler trim kit, new air vent. Adapted to flu pipe. Adapted to hot and cold pipes of the water heater. Adapted to gas line. Installed new flu pipe both systems are tested and working properly at this point. Model # RG240T6N Serial # YM50704448 System is financed
Paul T.
Came out today for a Weil McLain boiler model #cg-6-spdn, cp #3107747. Upon arrival the homeowner stated that the system would come on but not heat the home. I removed the access panel and noticed that the system has a standing pilot and it was not lit. I tried to light the pilot but had no success. I removed the pilot assembly and noticed that the thermocouple was severely charged. I recommend replacing the thermocouple to start and the homeowner agreed. I replaced the thermocouple and lit the pilot. Once I powered the system back up the system ignited. The systems burners and burner box are covered in dust . I highly recommended performing preventative maintenance for the boiler. The homeowner stated that he would schedule another time for maintenance. The system is operating at this time.
Matthew M.
Completed for Goodman system installation, furnace, evaporator coil, condenser, Honeywell filter cabiner, April Aire humidifier 700m. Left thermostat per customer request adapted to existing line set, venting, gas line, electrical. Outside replaced disconnect box, whip, pad. Ran new pvc drain to condensate pump. Ran vinyl tubing to Y fitting in drain pipe. Cycled and tested, system working properly at this time. FINANCING.
Paul A.
Original service call was to address an issue with Google Nest thermostat. Bypassed thermostat and rollout switch to perform combustion analysis. Found CO PPM levels around 3000 plus and immediately shut down the analyzer. Gas valve was also clicking on and off repeatedly and flames were rolling out. Shut off gas and power to the unit and advised the homeowner that the system will need to be replaced due to the multiple failures which include breached heat exchanger, failing gas valve. A company representative will be coming out to the property today between 12:30-1:30 to provide replacement options and discuss different financing options that we offer. The diagnostic charge can be refunded with a signed proposal for a new system. Chud will also determine if vent pipes are correct. There still may be an issue with the Google Nest thermostat as the homeowner put new batteries in it and it still was showing a fault of “no power” even with a common wire hooked up. Carrier high efficie
Matthew M.
Completed maintenance on attic system gas furnace. Checked all components for proper operation. System is in horizontal position with flue running out through roof, causing condensation to drip through flue pipe and into draft inducer. Cleaned orifice leading to pressure switch hose. Would recommend customer consider replacing this system due to its fair condition. System could be upgraded to a high efficiency system helping them save in their heating costs. Replaced filter, filter size 20x20x1. Cycled and tested, system working properly at this time.
Paul T.
Performed preventative maintenance for a Lennox furnace model #Sl280uh110v60-03, serial #5911j34646. I powered the system down and removed the access panels. Removed and cleaned carbon off of the flame sensor, cleaned out the burners and burner box. I replaced the pure air kit in the system. Checked all electrical connections to ensure that they are secure and in good condition. Performed humidifier service on a Aprilaire humidifier series 600. Ensured that the pressure switch was free of any debris. Tested the drain line and condensate pump with several bottles of water to ensure that there are no leaks or clogs. I powered the system up and called for heat. Took a combustion analysis test and received the following readings, o2 is at 12.4% and the co levels are 13ppm. The inducer amp draw is at .23 and the blower motor amp draw is at 7.4. I tested the humidifier for proper operation and leaks. The system is operating properly at this time.
Paul T.
Performed preventative maintenance for a Lennox system model #G61MP – 60C – 091–09, serial #5910E09876. Removed and cleaned carbon off of the flame sensor. Cleaned out the burners and burner box. Check all electrical components to ensure that they are secure and in good condition. Replaced the air filter size 16x20x1. Tested the drain line and condensate pump with several bottles of water to ensure that there are no leaks or clogs in the system. Made sure pressures switch are clear. Powered the system back on and called for heat. I observed the system starting normally and took a combustion analysis test. The inducer motor amp draw is at .23, the blower motor amp draw is at 5.2. The combustion analysis results are 11% for the o2, co is 11ppm. The system is operating properly at this time. I took a look at the nest thermostat and it is only off by 2°. In my professional opinion changing the thermostat will not fix this issue. The system is operating properly at this time.
Paul T.
Performed preventative maintenance for 3 heat pump systems. System #1 located in the attic, model #CBA38MV-018/024-230, serial #1618F16416. The evaporator coil’s are clean and in good condition. Tested the drain pan and drain line with several bottles of water to ensure that there are no leaks or clogs in the system. Replaced the air filter (homeowner supplied) size 20x20x5. Checked all electrical components to ensure that they are secure and in good condition. The blower is operating within the manufacturer’s specs. Supply temp is at 101°f. The condenser coil’s are clean and in good condition. The condenser amp draws are .80 for the fan and 9.96 for the compressor. System #2 located in the attic, model #Cba38mv-042-230-6-02, serial #1621j04024. The evaporator coil’s are clean and in good condition. Tested the drain pan and drain line with several bottles of water to ensure that there are no leaks or clogs. Replaced the homeowner supplied air filter size 20x20x5.
Matthew M.
Customer had very small gas leak coming from drip leg on boiler. Re doped and tightened drip leg. Tested for leak. No leaks present at this time.
Matthew M.
Installed new Goodman equipment. Project included new condenser pad. With new high voltage disconnect box an new high voltage. Adapted to lineset an did a r-11 acid flush. Adapted to drain lines. Adapted to high voltage added new 220 switch. An reused low voltage. An installed new thermostat. Filter size 20x24x1. System is tested and working properly at this time.
Keith R.
Performed air duct cleaning and sanitation on a 3 bedroom single system house house. All vents and ductwork are clear of dust and debris at this time. System is functioning properly at this time. Recommend duct cleaning every 3-4 years. Thank you for your business!
Paul T.
Performed preventative maintenance for a Goodman ac coil above a York furnace. The evaporator coil’s are clean and in good condition. tested the drain pan and drain line with several bottles of water to ensure that there are no leaks or clogs. Replaced the 401 air filter. Checked all electrical components needed for air conditioning to ensure that they are secure and in good condition. The blower motor amp draw is at 4.3. The temperature split is at a 19. The condenser coil’s are clean and in good condition. The condenser amp draws are 15.85 for the compressor and .94 for the fan. The refrigerant pressures are within normal range for the temperature outside today.
Frank B.
Customer called for system cooling but wouldn’t shut down at the customers set temperature. I found that the customer has a nest thermostat that they don’t fully know how to operate. It was set for home learning mode where it makes a schedule based oh the temperature you adjust to. Customer just wanted a standard setup with no schedule. I removed the schedule and the system was no operating as desired. Found no issue with the thermostat or that it was cooling beyond the setting. I then proceeded to perform the maintenance. Inspected all the electrical components. Confirmed proper high and low voltages. Tested the temperature split between the supply and return. System was operating at a 19° differential. Tested the amp draw for the blower, compressor and fan motor. All were operating within the manufacturer specs. Customer replaced the 16x20x1 air filter. System is operating properly at this time.
Paul T.
Came out today for a no ac call. Upon inspection I found that the condenser was not operating during a call for ac. I found the low voltage wire disconnected from the condenser. I reconnected the low voltage wire and the system started right up. The compressor is making a loud grinding noise. I connected my gauges and noticed that the system was practically empty of refrigerant. Low side pressure of 16 psi. Goodman system. At this point due to the age of the system it should be updated to a system that utilizes 410-A refrigerant. The system is not operational at this time. I will reach out to Chud's comfort advisor with all the details. See photos.
Paul T.
Performed preventative maintenance for a Coleman system model #CC7B4821SA, serial #W1D6510946. The evaporator coil’s are clean and in good condition. Tested the drain pan and drain line with several bottles of water to ensure that there are no leaks or clogs. Replaced the air filter (homeowner supplied) size 20x25x4 Merv11. Checked all electrical components needed for air conditioning to ensure that they are secure and in good condition. The blower motor amp draw is within normal range. The temperature split is at a 20. The condenser coils are clean and in good condition. The condenser amp draws are 1.6 for the fan and 9.5 for the compressor. The refrigerant pressures are within normal range for the temperature outside today. Homeowner is pre paying for fall heat maintenance.
Matthew M.
Completed Bradford white 75 gallon, gas direct vent hot water heater installation. Adapted to existing gas line, water lines, and venting. Replaced st 12 expansion tank. Cycled and tested, system working properly at this time.
Paul T.
Came out today for to look at a hot water heater that is not operating properly. Upon inspection I found that the system was not heating the water due to a tripped safety switch in the blower motor. The hot water heater would need to be replaced. This is a natural gas, direct vent, 75 gallon hot water heater.
Keith R.
Performed air duct cleaning and sanitation on a 3 bedroom single system house. All vents and ductwork are clear of dust and debris at this time. System is functioning properly at this time. Recommend duct cleaning every 3-4 years. Performed first floor dryer vent cleaning. Dryer vent, duct, flex hose and lint trap are all clear of lint and debris at this time. Dryer is functioning properly at this time and exhaust flow is optimal. Recommend dryer vent cleaning every 1-2 years. Thank you for your business!
Paul T.
Came out today for a leaking hot water heater. Upon inspection I found that the expansion tank failed and the relief valve opened to release the pressure. The relief valve will no close properly and is causing a leak. My recommendation is to replace the hot water heater and expansion tank. 50 gallon, natural gas, chimney vent. See estimate for details and photos.
Keith R.
Performed air duct cleaning and sanitation on a 4 bedroom single system house post construction. All vents and ductwork are clear of dust and debris at this time. System of at this time. Recommend duct cleaning every 3+4 years. Thank you for your business!
Paul T.
Lennox condenser condenser was struck by a falling tree. The condenser fan took most of the force. The condenser fan motor is pulling a high amp draw and will most likely burn out soon. To prevent this Chud recommends replacing the condenser fan motor, fan blade (4 blades) and capacitor (45+10). 4-1-22-PT- Removed the old existing fan from the condenser as well as the capacitor. Installed a new fan motor, fan blade and 45/10 capacitor. Cleaned out all the pine needles and debris from the base of the condenser. All the debris were from the tree that fell. I called for AC to test the system. The refrigerant pressures are still within normal range for the temperature outside. The amp draws for the condenser are .8 for the fan and 9.03 for the compressor. These are normal amp draws for this system. The temperature split is still at 20+. The system is operating properly at this time.
Paul T.
Performed preventative maintenance for a Lennox AC system. The evaporator coil's are clean, the drain pan and drain line are clear of debris. I observed the system starting normally. The temp split it at 20+. The condenser coils are clean. The amp draws for the condenser are 8.25 for the compressor and 1.4 for the fan. The fan has a high amp draw. See estimate for details. Checked all electrical components needed for air conditioning. The clean air kit was installed last season.
Keith R.
Performed 2nd floor dryer vent cleaning. Dry vent had a big clog near the opening. At this time dryer vent, duct, flex hose and lint trap are all clear of lint and debris at this time. Dryer is functioning properly at this time and vent has optimal air flow. Recommend dryer vent cleaning every 1-2 years to avoid further clogs and dryer fires. Thank you for your business!
Paul T.
Came out today to replace a condenser coil. Cut out and removed the old condenser coil. Brazed in the the coil . Pressure tested for leaks and attempted to pull a vacuum. The system would not pull a vacuum into microns. Cleaned out the refrigerant lines and there was oil and moisture in the lines. Once I cleaned out the lines the system was able to pull a vacuum into 750 microns. I charged the system with 9lbs of 410 a refrigerant. The pressures are within normal range for the temperature outside. Tested the system for both heating and air conditioning. The system is operating properly at this time.
Paul T.
Came out today for a Lennox condenser not operating with an error code of 411. Upon inspection I found that the system had no refrigerant pressure at all. I charged the system with nitrogen and immediately heard a hissing sound from the condenser. I found a leak in the connection for the cap tube going into the coil. The condenser will have to be replaced and Chud will have to check the warranty.